THE Flip 32 - F3 - Omnibus Pro (with baro option)
Same great board with Added current sensor.
The Flip32 Omnibus flight controller uses the MPU6000 over SPI for the best possible flight performance. Along with the MPU6000 and an AB7456 OSD chip (an upgraded MAX7456) for the BetaFlight integrated OSD. You won't need a PDB with this build because there is a high performance 5v, 1.5a STMicrocontroller L78 voltage regulator, so you can plug the flight battery right into the flight controller.The Flip32 Omnibus flight controller the frist F3 flight controller with a MAX7456 OSD chip directly connected to the flight controller, so it can be configured from the BetaFlight configurator.
This flight controller requires BetaFlight 3.0 & Betaflight configurator to take full advantage of the OSD
INSTALL THE BETAFLIGHT CONFIGURATOR
NEW OSD tab in Betaflight configurator lets you setup and configure OSD settings on the fly!
Flip32 OmniBus was designed a 36mmx36mm (30.5mm mount holes) community version of his AIO boards. It’s called Flip32 OMNIBUS and it’s outstanding. The great thing is that the board is based on what the community really wanted and it allows a very clean build by providing pin holes for almost every connection. You can power it directly from your battery by using BAT/GND pins. The following list some of the components included:
STM32 F303 MCU (Spi connected to Gyro)
MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
OSD (configured over Betaflight UI)
MicroSD card slot
SBUS/PPM + DSMX Ports
current + voltage + rssi + buzzer as pins
4x 3 pin holes for ESCs + 4x signal pin holes
IR pins for lap timing transponder
The Flip 32 OmnibusF3 flight controller is an integrated flight controller and OSD specifically designed for ease of use and outstanding flight performance. The MPU6000 inertial motion sensor was chosen for it's high reliability, accuracy and update speed. This board has no problem running fast loop times and ESC protocols. There is an onboard GYRO along with an On Screen Display (OSD) chip directly connected to the main processor (MCU). This tight integration between the MCU and the OSD enables fast updates to the display and easy configuration of the OSD, which is managed straight from the BetaFlight configuration tool. You no longer need to worry about the extra hassle of configuring your OSD with a USB/UART adapter and 3rd party configuration tool, it's all built into the flight control software.
The Flip 32 OmnibusF3 was designed to work specifically with BorisB's amazing BetaFlight firmware. Boris is a control system expert and has implemented his own "ISA-PID compensator" based PID controller, called the BetaFlight PIDc, that gives an almost-predictive control for that super locked-in stick feeling. Download the BetaFlight configurator to flash and configure your quadcopter here: https://chrome.google.com/webstore/detail/betaflight-configurator/kdaghagfopacdngbohiknlhcocjccjao
Finally, for maximum ease of use, the Flip 32 OmnibusF3 has an onboard voltage regulator that can easily handle up to a 5s battery. No need to mess with a PDB, just plug your battery straight into the flight controller and you're ready to go! Along with the robustly engineered power management system on the OmnibusF3, special precautions have been taken to ensure that the sensitive OSD chip is well protected, so you don't have to worry about any problems with your OSD. even on 5s!
To power the board you have two options. Either connect battery directly to BAT/GND or supply 5V on one of the ESCs connections. However you obviously want to have voltage display in your OSD so just connect BAT/GND to your LiPo (up to 4S).
To power your VTX and camera you have even more options. Out of the box RAM is not connected to anything. That leaves you with following alternatives.
Short RAM and VBAT to get LiPo voltage. This would be unfiltered and could cause video noise.
Short RAM and 5V to get filtered 5V from the board. This would provide clean video but 5V is probably not enought for most VTX on the market.
Provide clean voltage from external BEC . It will provide filtered 10V for HS1177 and a VTX.
Updated:SBUS/PPM Pin - Pin define changed since Betaflight v3.0 RC5, we use SBUS pin to read PPM input too. This can be changed Via the GUI. These are setup for SBus or PPM pin out of the box.
Baro Option